LOW-PRESSURE IN-GROUND Lift Parts 

All Brands Listed Below

Globe, Joyce, Wayne, Gilbarco, Rotary

Manitowoc, Benwil, Western & Weaver

And Many Others 

Between 9 AM and 3:00 PM (central-zone) Mon thru Fri

QUICK LINKS TO ITEM LOCATIONS ON THIS IN-GROUND LIFT PARTS PAGE...

Challenger In-Ground Lift Parts LINK

FORE & AFT" Heavy Duty Lift Repair Part LINK

Globe In-Ground Lift Parts LINK

Gilbarco In-Ground Lift Parts LINK

Joyce In-Ground Lift Parts LINK

Manitowoc In-Ground Lift Parts LINK

Rotary Lift In-Ground Seal Kits LINK

Rotary In-Ground Equalizer Parts, "Flipper Latch" Repair Kits , New Arms & Superstructures, 

Complete Equalizer Rescue Kit if Box is Filling With Dirt and Lift Equalizer Won't Lower Anymore.

Save That Rotary 2-Post In-ground Lift with These Rescue Repair Kits,

could give you another 5-10 years of service-life LINK 

Rotary Equalizer Parts and Safety Flipper Latch Kits LINK

Spotting Dish For Lifts LINK

Safety Legs for In-Ground Lifts LINK

TANKS for In-Ground Lifts LINK

Wayne In-Ground Lift Parts LINK

Western In-Ground Lift Parts LINK

Weaver In-Ground Lift Parts LINK

Weaver Fore & Aft Parts LINK

In-Ground Lift: Arm-Friction Washers LINK

FOR ARM SLEEVE & ADAPTERS GO TO THIS LINK

"Clean-Out Auger Tool" for Safety Leg Tubes & Equalizer Rack Bar Tubes LINK

(Lift won't lower to floor? Could be that Oil Dry or other Debris has filled the bottom of the tubes 

enough to not allow the rack bars or safety leg to lower all the way.)

The difference between "Semi-Hydraulic Lifts" & "Full Hydraulic Lifts" LINK

GLAND RING CHART

Find Seals On "Low-Pressure" In-ground Lifts

Identification COMPARISON CHART 

Click to Enlarge then Print it if you want to.

Model Number & Other Equipment Identification Handy When You Call. 

Best Regards, Smitty

Oil Tanks For All "Full Hydraulic"

In-Ground Lifts 

In-Ground Low-Pressure Lifts that last & last & last...

Underground tank spring a leak? Save that lift by using one of these to efficiently replace the old tank by mounting it next to the wall and piping to the oil valve to save a large underground installation bill. 

Tanks are 14 to 16 inches in diameter depending on the capacity.

Tanks can be buried under the shop floor or mounted on the floor surface near the 1-1/4 inch oil valve that operates the lift. 

Call for price on Fiberglass Coated Tanks for installing it underground. 630-678-9010

Fore & Aft Style Lift Tanks are also available

 Tank Kit Includes: Filler Plug with Dipstick & Low Oil Control Tank Float.

Certified Tanks

36 Gallon Capacity Tank: 14-inch diameter X 58-inches tall

Used for ALL brands with one 10-5/8 diameter hydraulic cylinder. 

Tank has 1-1/4 inch NPT oil pipe outlet on bottom and 

1/2 inch NPT air pipe inlet on top.  

9801C weighs approximately 124 pounds

CALL 630-678-9010 FOR QUOTE

Same Tank as Above, but "Fiberglass Coated" for In-Ground Installation

CALL 630-678-9010 FOR QUOTE

42 Gallon Capacity Tank: 16-inch diameter X 52-inches tall

Used for ALL two post side by side with 8-1/2 inch 

or smaller diameter hydraulic cylinders. 

Tank has 1-1/4 inch NPT oil pipe outlet on bottom and 

1/2 inch NPT air pipe inlet on top.  

9802C weighs approximately 125 pounds

CALL 630-678-9010 FOR QUOTE

Same Tank as Above, but "Fiberglass Coated" for In-Ground Installation

CALL 630-678-9010 FOR QUOTE

47 Gallon Capacity Tank: 14-inch diameter X 74-inches tall

Used on Fore & Aft lifts that call for this tank size 

Tank has 1-1/4 inch NPT oil pipe outlet on bottom and 

1/2 inch NPT air pipe inlet on top.  

9805C weighs approximately 145 pounds

CALL 630-678-9010 FOR QUOTE

Same as above with Fiberglass Protective Coating

CALL 630-678-9010 FOR QUOTE

62 Gallon Capacity Tank: 16-inch diameter X 75-inches tall

Used on Fore & Aft lifts that call for this tank size 

Tank has 1-1/4 inch NPT oil pipe outlet on bottom and 

1/2 inch NPT air pipe inlet on top.  

9804C weighs approximately 145 pounds

CALL 630-678-9010 FOR QUOTE

Same as above with Fiberglass Protective Coating

CALL 630-678-9010 FOR QUOTE

Oil Tank Plug & Dipstick - 1-1/2 inch Diameter (NPT) Thread

$110.00 each Delivered   

Oil Tank Plug & Dipstick - 2 inch Diameter (NPT) Thread

$114.00 each Delivered   

"Low Oil Control"

Tank Float

These Floats are 100% Aluminum!

Replace your tank float if you were using your lift while low on oil causing the float to clang against the bottom opening of the tank. Replace it before the old float gets jammed in the tanks bottom opening and you end up having a car stuck up in the air when the float gets stuck and refuses to allow oil back into the tank.

$69.00 Delivered 

IN-GROUND LIFT  AIR VALVES

For Any Brand Lift

1/2 Inch NPT(F)

This is a picture of solid brass body Non-Locking or Locking Style Valves 

with 1/2 inch NPT Female Threads

 NON-LOCKING STYLE AIR VALVE 

ALL BRASS BODY

1/2 inch NPT Female Thread

The Non-Locking style air control valve is for SINGLE-POST SEMI-HYDRAULIC LIFTS

that only have ONE valve (the air valve shown) that operates the lift.

FK-303-500 Non-Locking Valve

$89.00 each Delivered 

FK-303-500 Valve and 9642 Exhaust Muffler $109.00 Delivered 

(Muffler shown 5 images below)

LOCKING STYLE AIR VALVE

The Locking style air control valve is for TWO-POST or SINGLE-POST  FULL-HYDRAULIC LIFTS

that have two separate valves, an Air Valve and an Oil Control Valve to operate the lift.

FK-302-500 Locking Valve  

$89.00 each Delivered   

FK-302-500 Valve and 9642 Exhaust Muffler $106.00 Delivered 

(Muffler shown 4 images below)

 LIFT AIR VALVE REPAIR KIT 

PACKING KIT FOR AIR VALVES SHOWN ABOVE

Completely replaces packing, spring & "O" ring on 

the Intake and Exhaust sides of Air Valve (SHOWN ABOVE)

For Kingston and Conrader Air valves ONLY

 $35.00 Delivered 

 LIFT AIR VALVE REPLACEMENT LEVERS 

LEVERS FOR AIR VALVES SHOWN ABOVE

 $29.00 Delivered 

 $29.00 Delivered 

 

 

  Air Exhaust Muffler

• 1/2 Male Pipe Thread Connection 

• Heavy Duty Aluminum Construction

• Quiets Down Air Exhaust Noise

• Muffler won't rust!

$45.00 Delivered

         

  Our Quietest Muffler

Non-Rusting Aluminum

1/2 NPT Male Pipe Thread

$44.00 Delivered 

 Click to Enlarge Image

  Muffler with "Oil Mist Trap"

 Install with drain cock pointing down only.

Non-Rusting Aluminum

1/2 NPT Male Pipe Thread

$59.00 Delivered 

In-Ground Lift 1-1/4 inch NPT(F) Oil Control Valve

Replace that sticky, worn out, leaky oil valve with a brand new one!

Horizontal Valve Style

 (Handle color may vary)

The Original Dependable Oil Valve Used On "Full-Hydraulic" In-Ground Lifts!

 Brass 1-1/4 Inch NPT(F) Valve with Steel Handle

Replacement External Spring with Bushing 

For 1-1/4 inch Oil Valve (above) and Others

Includes Poly Bushing & Spring, use with or without bushing

$38.00 each Delivered

Replacement External Spring 

For 1-1/4 inch Oil Valve (above) and Others (No Poly Bushing)

$38.00 each Delivered

In-Ground Lift 1-1/4 inch NPT(F) Oil Control Valve

Used on Western and Other Brand Lifts

Ball Valve Type Shut-Off Mechanism

Vertically Mounted Style

For In-Ground Full Hydraulic Lifts

 Brass 1-1/4 Inch NPT(F) Valve with Steel Handle (Spring Loaded Return)

$325.00 each Delivered

Wheel/Tire Spotting Dish Kits

For mounting on floor to use as a gauge where to spot vehicles prior to raising on lift. 

Floor mounting hardware included.

Vehicles can use 3 positions, one in front of the dish, one on the dish and 

one behind the dish, depending on the length of the vehicle.   

Each Rotary Dish Kit $45.00 Delivered  or get two for $80.00 Delivered

SIZE of this spotting dish is 12 inches wide X 10-1/2 inches

One Dish $45.00 Delivered

Two Dishes $80.00 Delivered  

FREE SHIPPING TO COMMERCIAL ADDRESSES ONLY!

FOR RESIDENTIAL DELIVERY - ORDER BY PHONE 630-678-9010 

Wide Heavy Duty Steel Spotting Dish

This Spotting Dish is "W-I-D-E-R" and has more reach.

Wider so you can see it easier out the door while spotting the vehicle on it.  

Narrower cars fit it while centered on the lift.

No name on it, well made HEAVY GAUGE STEEL, painted yellow.

 Includes Mounting Hardware.  

SIZE of spotting dish is 15 inches wide  X 10-3/4 inches

Wide Heavy Duty Steel Spotting Dish $49.00

One Dish Delivered

TWO Wide Heavy Duty Steel Spotting Dishes 

$10.00 Discount

 Two for $88.00 Delivered 

Dual Heavy Duty Steel Spotting Dish

Yellow color like the one shown above Only Taller.

Like above but "Duel"

 $64.00 Delivered 

20-1/8 inches tall X 15 inches wide! 

Great for spotting long or short vehicles on a lift!

FREE SHIPPING TO COMMERCIAL ADDRESSES ONLY!

FOR RESIDENTIAL DELIVERY - ORDER BY PHONE 630-678-9010 

Is Your Lift Chattering? 

Help stop the problem by adding "Metholardate" to the oil.

Hydraulic Oil Additive

"Metholardate" adds lubricity to the hydraulic oil and "Sticks" to the internal metal surfaces protecting them. New seals tend to provide more sealing surface which can cause the lift to hang-up on the way down, especially if it doesn't have a load on it. It is recommended for Surface Lift Cylinders and 

In-Ground Cylinders or anytime the lift is "chattering" when going up or down. 

 

1 Qt. Can 9960-25 $49.00 Delivered 

1 Gallon Can 9960-01 $109.00 Delivered 

In-Ground Lift Arm-Friction Washers

6 Inch Flat Disk Style with 3/4 Hole In Center

Non-Metallic Poly Type Arm Friction Disks. When GREASED and fit between 

the lift arm and superstructure, the arm swings more easily. 

Mating surfaces on superstructures should be cleaned & greased before installing for best performance. 

Set of Four 1/16 in. thick Arm Disk/Bushings $69.00 Delivered

Set of Four 1/8 in. thick Arm Disk/Bushings $69.00 Delivered

Fits ROTARY In-Ground "DTO-28"

 2-Post Low-Pressure Lifts

For Twin-Post Rotary Low-Pressure

In-Ground Lifts that need complete new Arms,

Superstructures & Flip-Up Style Adapters.

CALL FOR QUOTE 630-678-9010

Call 630-678-9010

Flip-Up Adapter Kit For ROTARY

  Includes High Step, Low Step and Pin that holds them together. Two different attaching swivel pins included for use with either surface lift arms or in-ground lift arm sleeves. 

   One Kit $79.00 Delivered

ROTARY Replacement Equalizer Parts

Replacement Equalizer Cover Plate & Repair Parts 

for DTO Model Two-Post Low-Pressure In-Ground Lifts 

SAVE THAT Rotary 2-POST Low-pressure In-ground Lift! 

(#4) Steel Cover Plate For Floor  $129.00 Delivered  

(#2) Equalizer "I" Beam Frame WITH SLIDER BLOCKS(-05)  $1398.00  Delivered 

(#2) Equalizer "I" Beam Frame WITH ROLLER BEARINGS (-05R) $1398.00  Delivered 

(#5) "Safety Flipper" Latch Repair Kit For ROTARY LIFTS  

$208.00 Delivered 

Includes 2 latches and pins for welding to "I" beam  

DIRT FILLING YOUR ROTARY 2-POST LIFTS EQUALIZER

BOX SO IT WON'T LOWER ALL THE WAY?

ROTARY "DTO" Style two post in-ground lifts are one of the most dependable 

lifts ever made, but they had one major flaw and that was the fact that the 

equalizer box the "I" beam equalizer lowered into would rust through allowing 

dirt and back-fill to cause the lift to not lower completely.

Up until the time this kit was created, the only thing you could do was to 

excavate the equalizer box and install a new one at a cost of about three thousand

dollars, sometimes even more depending on who was doing the job!

Now you can solve the problem of equalizer box decay without 

breaking out your floor or doing any excavating or concrete work! 

If you've  got about 3 hours and want to save thousands of dollars in Rotary 

Equalizer Box replacement costs, or the cost of a new lift, 

all you'll need then is this kit to fix the problem...

NO EXCAVATING!

 

 

 

CLICK TO SEE ADDITIONAL IMAGE

This heavy duty rescue kit comes complete with rack bars, equalizer shaft, pinion gears, 

support housing, cover plate, anchor bolts, hardware kit and simple installation instructions.  

 

$2075.00 Delivered! CALL TO PURCHASE 630-678-9010

 

Measure the narrowest width of your Rotary Equalizer Box the "I" Beam Equalizer raises

in and out of...  they are either 4 inches wide or 4-3/4 inches wide.

 

 

Equalizer Rescue Kit 9760-09 for 4" Wide Equalizer Box  $2075.00

 

Equalizer Rescue Kit 9760-10 for 4-3/4" Wide Equalizer Box   $2075.00

 

 

---

 

Repair Parts for the Above Rack & Pinion Rescue Kit 

Pinion Gear $115.00 Each Delivered

    

---

 

Rack Bar $479.00 Delivered

      

---

 

Pillow Blocks

Right Hand $239.00 Each Delivered

   

---

 

Left Hand $239.00 Each Delivered

GLAND RING CHART

Find Seals On "Low-Pressure" In-ground Lifts

Identification COMPARISON CHART

HELPS YOU IDENTIFY THE BRAND NAME OF YOUR IN-GROUND LIFT 

Fore & Aft Truck & Bus Lift Parts

ROTARY, WEAVER, GLOBE,

Gilbarco, Manitowoc, just call

630-678-9010 

Rotary, Weaver, Globe

LINK TO FORE & AFT 

LIFT PARTS PAGE

Replacement Cylinders 

For Fore & Aft Lifts

Free UPS or other "Ground" Delivery to Commercial Addresses

Call for Challenger and other Brand "High-Pressure Cassette Lift" Parts

 630-678-9010

Safety Leg / Non-Rotators

For Single Post In-Ground Automotive Lifts

and Heavy Duty Fore & Aft Truck and Bus Lifts.

Single Post in-Ground Vehicle Lifts: Safety Legs actually serve a dual purpose. 

They not only act as a safety mechanism, but they also prevent the lift from being able 

to Turn or Rotate. (Ever see someone turn a small car around on a lift while it's up in the air?)

 Commonly called "Non-Rotators" they keep the pins on the bottom of the 

lift piston (plunger) from lining up with the slots in the cylinder casing.

(Pistons are removed from the casings by lining up the pins with the slots, and it's 

not too safe to have that happen with a car all the way up in the air.)

 

Fore & Aft Truck & Bus Lifts: Often they are just missing on some fore & aft truck lifts.... 

It could save you or at least your toolbox, oil drain or other equipment if a truck lift 

decides to come down on it's own.  Lifts can drop as quickly as the oil can be sprayed 

from an oil supply hose that's feeding the front cylinder if it pops.  

Pit located feed hoses can be up to 1 inch I.D. on older Truck & Bus lifts. 

 

Many times hoses are left hanging in a polluted mix of oil and water eventually weakening the hose causing it to fail. Unfortunately this has a way of happening when there is a heavy load on the front cylinder. You can't see the feed hose because they are located under the steel pit cover plates.  (Fore & Aft lifts should be inspected for preventive maintenance twice a year to 

 help prevent this scenario from happening.)  Fore & Aft Lift Hose LINK

      2-3/8 Outside Diameter Pipe

Foot release style (like above) for Single-Post Auto Lifts.

Any length stroke  $319.00 Delivered!

Measure the length of the cylinder stroke (in inches) from under the lift's superstructure to the concrete floor.

Minimum 60" stroke available (approximate measurement)

Overall Length of Safety Leg Pipe is 80 Inches (Can be trimmed shorter)

Specify length of stroke in inches =
Specify bolt diameter 5/8 or 3/4"  =

  NOTE! 3/4 BOLT ONLY AVAILABLE FOR 66 INCH STROKE

---

WANT AN EXTRA FLIPPER? Great for positioning vehicle for brake jobs, tire rotations, body work or other jobs where lift is not wanted at full height.

Lift can be set on Flipper approximately 30 to 35 inches off the floor. 

$135.00 added to your "foot released" safety leg order.

  Click to add extra Flipper to your Safety-Leg order

 

 

LINK To Non-Rotator Safety Leg Chart CLICK HERE

(2 Inch diameter safety legs available too, call 630-678-9010)

---

 

 

 

 

 

"Top release style" non-rotator/safety leg

Usually used on Fore & Aft Lifts or Recessed Single Post Lifts.

$398.00 Delivered 

Top Release Has Thumb Activated Pull Rod At Top Of Leg For Easy Flipper Disengagement

 

Specify length of stroke in inches  =
Specify bolt diameter 5/8 or 3/4 in. =

NOTE! 3/4 BOLT ONLY AVAILABLE FOR 66 INCH STROKE

 

---

 

NEW Telescopic Safety Leg/Non-Rotator

 

With 2nd Flipper in the Middle for Brake Jobs and Wheel Work

 

 

$529.00 Delivered

 

With 5/8 bolt on Top

 

For 66 inch Stroke Cylinder 

    

---

 

For 67 inch Stroke Cylinder 

 

---

 

For 68 inch Stroke Cylinder 

---

 

For 69 inch Stroke Cylinder 

---

 

For 70 inch Stroke Cylinder 

 

 

 

---

Multiple Flipper Safety Leg with

Flippers every 6 Inches!

Top release multiple flipper safety leg $698.00 Delivered  

Top Release Has Pull Rod At Top Of Leg For Easy Flipper Disengagement

ROUND 2-3/8 DIAMETER HEAVY WALL PIPE

 

 

Specify length of stroke in inches =
Specify bolt diameter 5/8 or 3/4 inch =

NOTE! 3/4 BOLT ONLY AVAILABLE FOR 66 INCH STROKE

Safety-Leg & Equalizer Rack-Bar Tube Clean-Out Tool/Auger

Lift not going down all the way? Losing clearance for lifting low profile vehicles?

 It could be because years of Oil-Dry and other "Floor Crap" slowly building up inside the

pipe casing the safety-leg lowers into. Two-Post lifts sometimes accumulate hardened debris

and oil-dry in the equalizer rack bar tubes as well.  

The rack bar pressing down on that crap every time it's lowered packs it so hard 

that just vacuuming it out is like trying to vacuum hardened concrete.  

This handy tool is a long Steel Auger that fits down the pipe in the floor

and loosens the hardened, packed oil-dry and whatever else managed to fall

down there so you can pull it out loaded on the auger itself and then vacuum the remainder out so the 

pipe is as clean as a babies ass!  (Or maybe even cleaner in some cases...)

Auger has a two piece extended handle long enough to clean out any safety-leg tube or rack-bar tube.

It has a loop at top to insert something to turn it.   Made to last!

SAFETY LEG/RACK BAR TUBE CLEAN-OUT AUGER. $249.00 Delivered

SEALS for Rotary In-Ground Lifts

Complete with easy to follow installation instructions

Kit for 8-1/2 diameter Rotary Lift Cylinder With 6-bolt Aluminum Gland Ring

Use a magnet to determine the type of metal the gland ring is made of, 

this kit is used with a 6-bolt aluminum gland cylinder.

These kits directly below are for ROTARY brand Low-Pressure in-ground lifts  

8-1/2" DIAMETER SEAL KIT FOR LIFTS WITH 6-BOLT ALUMINUM GLAND RING. 

This kit comes with new (JG620 style) gland ring, (JG220 style) seal & spring, 

brass bleeder plug, new grade-8 bolts & washers and installation instructions.

Seal & Gland "COMBO KIT" 8-1/2 Inch 

S-1721/21B  (J136)

$129.00 Delivered (Delivered)

WANT THE RUBBER SEAL ONLY from the kit above?

 8-1/2 in. Diameter (JG220) seal kit for Rotary lifts with 6-bolt aluminum gland ring  

$72.00 Delivered 

Includes seal & spring & install instructions (NO NEW Gland ring, Bolts or Bleeder Plug) 

Rotary 8-1/2 inch New Gland Ring  

8-1/2 inch 6-bolt aluminum Gland Ring JG620

$84.00 Delivered  

"DELIVERED" on this website means "FREE SHIPPING" to Commercial Addresses

 

Seals for Low-Pressure ROTARY In-Ground Lifts

10-5/8 Diameter Combo Kit For Rotary Lift Cylinder 

With 6-bolt Aluminum Gland Ring

10-5/8 INCH DIAMETER SEAL KIT FOR LIFTS WITH 6-BOLT ALUMINUM GLAND RING  

this kit comes with new (JK622 style) gland ring, (JK227 style) seal & spring,

(JX207 style) brass bleeder plug, new grade-8 bolts & washers and installation instructions.

Use a magnet to determine the type of metal the gland ring is made of, 

this kit is used with a 6-bolt aluminum gland cylinder.

Seal-Gland Combo-Kit 10-5/8 1799/99B (J134)

10-5/8 Kit  $149.00 Delivered

 WANT THE RUBBER SEAL ONLY from the above Combo kit? 

 10-5/8 in. Diameter 1799 (JK227) seal kit for Rotary lifts with 6 bolt aluminum gland ring  

$85.00 Delivered 

Includes seal & spring & install instructions (NO NEW GLAND, Bolts or Bleeder Plug) 

Rotary 10-5/8 inch New Gland Ring  

NEW Gland Ring, 6 Bolt Aluminum 

$98.00 Delivered 

Rescue that older  Rotary 10-5/8 cylinder with this NEW Gland Ring / Seal & Bearing kit!

Adds a new replaceable upper bearing to the cylinder for older cylinders that have non replaceable bearings. Easy to install, also updates the old JK227 seal to the new style seal LINK

SAVE THAT Rotary 2-POST Low-pressure In-ground Lift! 

Wobbly Shaky Pistons?

Changing seals again & again and they're still leaking even when fairly new?

 For Any 6-Bolt Aluminum Type Gland "In-ground" Rotary Lift...  

Cut-away shows new bearing surface

This Upper Bearing & Seal Kit for LOOSE Pistons Can Help Solve The Problem.

Has Adjust-To-Fit Replaceable Bearing for better fitting on differently worn pistons.

You can try this test... 

While lift has no vehicle on it, raise your lift until it tops out, then lower it about an inch or two. 

With the controls at "neutral" grab the superstructure (where the arms attach) and try shaking it back and forth hard. If the piston "wobbles" or has any "side to side" movement, that means the top bearing is worn inside the hydraulic cylinder and a small gap is being created between the piston and

 the seal allowing oil to "burp" past.. Seals can flex a little to make up for some play in the bearings, but if the bearing is too worn, even brand new seals can't prevent oil from leaking past.

When a vehicle is on it the same wobbling happens, but when you raise the lift all the way, the flange on the bottom of the piston seats against the inner top of the cylinder and holds the piston steady preventing the movement that allows oil to leak past.  Most of the leaking happens during the act of wobbling, 

while raising or lowering the lift, or if you only have it up part way like when doing a brake job.

  This bearing/seal replacement kit for Rotary 6-bolt Gland Rings adds a new upper bearing to your lifts hydraulic cylinder effectively limiting the extra play from old worn cylinder bearings.  The kit also includes a new seal style, converting the cylinder from the old style seal that had a 

spring on the bottom to the new JG227 Rotary Seal. 

The new bearing is replaceable too, allowing you the ability to maintain your older lift for years of added service capability. 

Helps stop leaks due to misaligned piston and can add YEARS of service to 

your otherwise dependable Rotary in-ground lift!

 For SIX Bolt Gland Rotary Cylinder Only

  8-1/2 inch "Adjust to Fit" Upper Bearing Gland & Seal Kit  (Same as JG629)

Has Adjust-To-Fit Replaceable Bearing for better fitting on differently worn pistons.

Regular Sale Price $549.00 DELIVERED!

   One Bearing Gland & Seal Repair Kit

Quantity SALE Two 8-1/2 inch kits for $1058.00 Delivered 

Two Bearing Gland & Seal Repair Kits

Replacement Seal Kit for Above "Adjust To Fit" Gland Kit  $120.00 Delivered

Includes replacement ATF Bearings

Replacement Nylatron Bearing Insert for OLD STYLE NON-A.T.F. Bearing Kits $79.00 Delivered 

NOTE NOT FOR THE ATF GLAND RING ABOVE

"Zero Leak Technology" 

8-1/2 inch Upper Bearing Gland, Bearing, Wiper & Seal Kit for Rotary Lifts 

Includes 8.5 Inch "Adjust-To-Fit" Bearing  

Manufacturer states that this seal kit should eliminate most persistent seal leaks

Has Adjust-To-Fit Replaceable Bearing for better fitting on differently worn pistons.

Regular Sale Price $698.00 DELIVERED!  

SALE Two 8-1/2 inch Z. L. T. - A. T. F. Bearing kits ($30.00 Off)  $1358.00 Delivered 

Replacement Seal Kit for Above 8.5 inch "Adjust To Fit" - Z. L. T. Kit  $349.00 Delivered

10-5/8  Z. L. T. - A. T. F. Kits available too, Call 630-678-9010

"DELIVERED" on this website means "FREE SHIPPING" to Commercial Addresses

---

10-5/8 inch 6-Bolt Upper Bearing Gland & Seal Kit 

(Same as JK629) Fits Rotary 6 Bolt Gland Rings, cylinder numbers JK1113 through JK1299. 

The cylinder number is located on the side of the piston at the top just below the superstructure.

Has Adjust-To-Fit Replaceable Bearing for better fitting on differently worn pistons.

 Your Cost $789.00 DELIVERED!

ROTARY LIFT Seal Kit JG227

FOR 8-1/2 INCH DIAMETER PISTON "BLUE SEAL" KIT SPECIFICALLY FOR ROTARY LIFT WITH 8-BOLT STEEL GLAND RING. Kit comes with seal and installation instructions. These seal kits are installed without removal of the 8-bolt steel gland, just by turning the piston 90 deg. The piston drops down far enough to pull the seal and replace it.  They are also used on some six bolt steel gland applications where you must remove the gland completely to install them. 

Bearings on these 8-bolt cylinders can be replaced if needed by ordering a bearing kit. 

Look below for more about the bearing replacement kits. 

Genuine Rotary Part

  $87.00 each Delivered

Rotary Original JG227  8-1/2 inch diameter Seal Kit

Same Kit, Only Supplied By Seal Company $75.00 Delivered

10-5/8 INCH DIAMETER SEAL JK238 SPECIFICALLY FOR ROTARY LIFTS 

WITH 8-BOLT STEEL GLAND RING.

  Rotary # JK238KIT Rotary 10-5/8 Seal Kit

$110.00 Delivered  

"Bearing & Seal Kit" for 8-Bolt Steel Gland Cylinders

Bearings Worn On ROTARY 8-Bolt Steel Gland Cylinder?

Seals leaking & Pistons Wobbling? or Binding Cylinder Movement?

 ORIGINAL PARTS

Seal, "O" Ring and Replacement Bearing Kit for 8-Bolt Rotary Steel Gland Type Cylinders.  

If piston "wobbles" or seals seem to be leaking for no good reason, you may need to replace the removable "Nylatron" bearings in the 8-bolt gland.  You can try this test... While lift has no vehicle on it, raise your lift until it stops, then lower it about an inch or two. With the controls at "neutral" grab the top of the superstructure where the arms attach and try shaking it hard, if it "wobbles" or has side to side movement, that means the top bearing is worn inside the cylinder and a gap is being created between the piston and the seal allowing oil to escape.  When a vehicle is on it the same thing happens, but when you raise the lift all the way, the flange on the bottom of the piston seats against the inner bearing of 

the cylinder and holds the piston steady. 

Most of the leaking happens during the act of raising or lowering the lift, or if you only 

have it up part way like when doing a brake job... 

This kit comes complete with NEW seal, 2 bearings, 1 "O" ring, bleeder plug and new bolts. 

One Kit Does One (8-bolt Steel Gland Type) Cylinder

8-1/2 inch seal / bearing / O-ring kit 

$120.00 Delivered = Free Shipping

10-5/8 inch (8-bolt Steel Gland Type) Seal / Bearing / O-ring kit 

$197.00 Delivered 

WEAVER LIFT PARTS

Weaver/Challenger Single Post Lift Seal Kits

(These are special seal kits that help prevent leaks due to worn or scarred cylinder pistons) 

Link to Weaver Single Post Cylinder Gland Picture

Link to one more Weaver Gland Ring 

(Note the grease fitting on it, should be greased twice a year)

Seal Kit and parts for Weaver Single Post In-Ground Auto lift. 

Piston diameter is 10 5/8 inches, Seal Kit consists of wiper, rope wiper, gland gasket, 

and 3 chevron style seal packing and installation instructions.  

Replaces Weaver Kit # KL159S   

10-5/8 = 10.6250  

10-5/8 inch Seal KIT for single post lifts  

$189.00 Delivered

10-5/8 Packing Expander Located Under Seals 

CLICK TO SEE IMAGE

(Image of 7.5 Expander, but looks the same as a 10-5/8)

(Spring Loaded to apply pressure on packing) 

Each $259.00 Delivered 

---

 

Set of Replacement Springs ONLY $46.00 Delivered 

            

 

---

Weaver EC881 and Challenger C881 twin post 

in-ground lift Seal Kits. 

Link to Weaver two post cylinder gland picture

7.5 inch SEAL KIT  Each $120.00 Delivered!

(TWO) 7.5 inch SEAL KITS $215.00 Delivered!

 7.5 inch Packing Expander (Located under the chevron seals)  

Check the springs in this part on your lift. Spring Loaded under the seals to apply pressure on seals. 

  Each $192.00 Delivered

          

 

 

CLICK TO SEE IMAGE

 

---

 

Set of Replacement Springs ONLY $39.00 Delivered 

          

 

 

---

WEAVER or Challenger TWO POST In-Ground LIFT

EQUALIZER PARTS

LINK to Weaver Equalizer Picture

Heavy Round Rack Bar 

 $649.00 Each Delivered 

Heavy Square Rack Bar 

 $429.00 Each Delivered

   1-7/8" X 1-7/8" Rack Bar

Rectangular Rack Bar  

$429.00 Each Delivered 

Common 57-1/2" X 1 inch diameter equalizer shaft  (Includes retaining rings)

$169.00 Delivered 

Other shaft lengths available, contact us.

Pinion Gear $130.00 Each Delivered

Weaver Pillow Block non-locking style that uses spacers behind it. 

(Spacers not included, use the old ones)

  $164.00 Delivered 

Challenger Pillow Block non-locking style 

LONGER STYLE - No Spacers

$195.00 Delivered 

Lift lock mechanism rebuild kit, has most hardware needed to replace worn or missing parts from Weaver 2-post EC881 and some other in-ground models that have the locking style pillow blocks. 

  NOTE! Must have locking style pillow blocks on your lift to install this kit, it will not work with

 non-locking style pillow blocks. 

$229.00 Each Delivered 

COMPLETE WEAVER/Challenger EQUALIZER KITS Listed Below

Kit includes 1-7/8" X 1-7/8" square rack bars, two pinion gears, standard pillow blocks 

with bearings, shaft spacers, equalizer gear shaft and shaft retaining snap rings. 

(Note: The steel block spacers behind the pillow blocks are not included, you should use the old ones

from your lift when you do your rebuilding, don't throw them away)

Measure the distance between the two piston "centers" to 

find the correct size for your lift.

Kit for 57.5 inch wide piston centers

WITH SQUARE RACK BARS

NON-LOCKING 

Each Kit $1650.00 Delivered 

          

---

 

Kit for 40 inch wide piston centers NON-LOCKING

WITH SQUARE RACK BARS

Each Kit  $1650.00 Delivered

 

Rectangular Equalizer Rack Bar Kit

Includes 1-3/4" X 1-7/8" rectangular rack bars, two pinion gears, standard pillow blocks with bearings, 

shaft spacers, equalizer gear shaft, shaft retaining snap rings. 

 

Kit for 57.5 inch wide piston centers NON-LOCKING

WITH RECTANGULAR RACK BARS 

$1650.00 Delivered

         

 

Order directly from our website, or by calling 630-678-9010 between 9AM & 4PM (Central-Time) Mon - Fri.  If you happen to get the "phone lines are busy message" please leave your phone number, as well as a detailed message and we'll call you back with the information you requested ASAP.

Weaver   Fore & Aft Lift Parts 

Parts for Weaver EC-100, 102, 103, 105, 106, 202, 203 series Fore & Aft Lifts.  

Front Piston Hydro Hose

Weaver (or other) 3/4" NPT $130.00 Delivered  

STOP Those Leaky In-Floor Oil Valves! 

  E-Z Installation of new core, seal, gasket, boot and roll pin. 

Aluminum Control Core Kit 

short stem (5-1/2 total length) 

$69.00 Delivered

Brass Control Core Kit 

short stem (5-1/2 total length) 

$125.00 Delivered135.00 Delivered

 Aluminum Control Core Kit

long stem (7-1/2 total length) 

$78.00 Delivered

 Aluminum Directional Core Kit

with short stem (5-1/2 total length) 

$125.00 Delivered

Brass Directional Core Kit

with short stem (5-1/2 total length) 

$169.00 Delivered 

 Aluminum Directional Core Kit

with long stem (7-1/2 total length) 

$198.00 Delivered

MORE BRASS AVAILABLE TOO! Call 630-678-9010

Trolley Axles, Ratchet Assemblies & Chain, Hoses, Tanks, Safety Legs, Saddles & Adapters... Contact us with your requirements and we will give you a parts quote...

Weaver 7-1/2 Diameter Seal kit for Fore & Aft Cylinders 

(They are different from the kits for a side by side twin post lift.) 

Each $130.00 Delivered 

       

---

 

7-1/2 inch Packing Expander  

(Spring Loaded to apply pressure on packing)   

Each $192.00

 

 

Set of Replacement Springs ONLY $39.00 Delivered 

          

 

 

---

 

Weaver 10-5/8 Diameter seal kit for Fore & Aft Cylinders  

(They are different from the kits for a single post lift)

10-5/8 = 10.6250  

 

Each $212.00 Delivered

      

 Kits are complete with installation instructions

---

 

10-5/8 Packing Expander Located Under Seals 

 

CLICK TO SEE IMAGE

 

(Spring Loaded to apply pressure on packing) 

Each $259.00 Delivered 

---

 

Set of Replacement Springs ONLY $46.00 Delivered 

            

 

GLOBE / Wayne Lift Parts

 

 

If you don't see what you're looking for... Contact us.  We've got them all!

(NEW GLOBE LIFT COMPLETE KITS FOR SALE!) LINK

 (These kits will replace the seal on 1 cylinder)

Old Style Lift Seal Kit Globe 7.5 inch diameter piston

This seal kit fits all 7.5 Globe cylinders. Includes: Wiper, Seal, Complete Set of Assorted Gaskets 

(You'll have a few left over) and Installation Instructions.   

For all 7.5 in. diameter Globe cylinders

 

Each Kit $219.00 Delivered

  7.5 inch diameter piston kit       

  

Old Style Lift Seal Kit Globe 8-1/2 inch diameter piston 

This seal kit fits all 8.5 Globe cylinders. Includes: Wiper, Seal, Complete Set of Assorted Gaskets (You'll have a few left over) and Installation Instructions.  Seal has ribbed rubber style expanding method instead of steel spring.   

For all 8.5 in. diameter Globe cylinders   

 

Each Kit $209.00 Delivered

8.5 inch diameter piston kit       

 These kits will replace the seal on 1 cylinder

 

Original Spring style kit available for 8.5 in diameter piston

Includes: Wiper, Seal, Spring, Complete Set of Assorted Gaskets (You'll have a few left over) and 

Installation Instructions.  Uses spring for expander instead of "rubber ribbed" style expanding

method. (Spring style may be a little easier to install than the ribbed style is.)

 Each Kit $215.00 Delivered

Original Spring Style Seal Kit        

GLOBE 8-1/2 STEEL GLAND RING FOR CYLINDER

NOTE: UPPER BEARING NOT INCLUDED

  $334.00 Delivered 

Globe 10-5/8 Cylinder Seals

Globe Single Post 10-5/8 Cylinder Parts Reference Drawing

LINK to Globe 10-5/8 cylinder gland picture

another identical cylinder image below

2nd LINK to Globe 10-5/8 cylinder gland picture

  Globe 10-5/8 Cylinder View (Gland has Twelve bolts and 12 point bolt heads are common, but sometimes they used "Allen Style " hex head bolts instead)

---

OIL PLUG AND DIPSTICK For 

GLOBE ONLY Semi-Hydraulic Cylinders

 Lifts with the PLUG in the center of the top of the piston. 

(NOT FOR 2-POST OIL TANKS)

(2.59 inch diameter thread)  Gasket Included

#10 & #11 in reference drawing above

$129.00 Delivered

  

This Original Globe Seal Kit fits Older 10-5/8 Cylinders

Includes: Wiper, Seal, Complete Set of Assorted Gaskets and Installation Instructions. 

Seal has ribbed rubber style expanding method instead of steel spring.  

Fits all 10-5/8 inch diameter Globe cylinders

 $215.00 Delivered

(These kits will replace the seal on 1 cylinder)

NEW Uni-Seal 10-5/8 Universal Packing Kit 

 Has more sealing surface for better seal

$229.00 Delivered

Original 10-5/8 Spring style Seal Kit  

For 10-5/8 inch diameter Globe Piston

 Includes: Wiper, Seal, Stainless-Steel Spring, Complete Set of Assorted Gaskets (You'll have a few left over) and Installation Instructions. Uses spring for expander instead of "rubber ribbed" style expanding method. (Spring style may be a little easier for you to install than the ribbed style is.)

$235.00 Delivered = Free Shipping

Globe Old Style 10-5/8 Cylinder WIPER COVER/GLAND RING

Original Style Steel Gland Ring

NOTE: UPPER BEARING NOT INCLUDED

$298.00 Delivered

   35054

 

NEW STYLE GLOBE 10-5/8 Seal & Wiper Kit

For Globe Lift Cylinders (Built after 2007)

Click to Enlarge Image

Call to purchase 630-678-9010

OIL PLUG AND DIPSTICK For 

GLOBE ONLY Semi-Hydraulic Cylinders

 Lifts with the PLUG in the center of the top of the piston. 

(NOT FOR 2-POST OIL TANKS)

(2.59 inch diameter thread)  Gasket Included

#10 & #11 in reference drawing above

$129.00 Delivered

  

The NEW Style GLOBE D.U.S.L. 10-5\8 Diameter 

Replaceable Upper Bearing Kit

"STOP THAT PISTON WOBBLE"

You can spot the difference from the Old Style Globe Cylinders because the New Style does NOT have a "Gland Ring" to remove, you remove the entire upper bearing from the cylinder, the seal, replaceable bearing and red wiper are inside it.  

Used on ALL New FS10 GLOBE Single Post Lift Kits link

 Available to upgrade your older Globe lift that may have upper bearing wear 

that may be causing "Piston Wobble" after 20+ years of service.  

You get the New Style A.T.F. (Adjust-To-Fit) Upper Bearing and 

the new style "Leak-Sealer" Packing Kit with Wiper 

$959.00 Delivered  

CALL 630-678-9010 TO PLACE ORDER

  New Style 10-5/8 Globe 9420-16TK Kit

Globe 12-5/8 Seal Kit  

Includes: Wiper, Seal, Complete Set of Assorted Gaskets and Installation Instructions. 

Seal has ribbed rubber style expanding method instead of steel spring.  

Fits all 12-5/8 inch diameter Globe cylinders

 $398.00 Delivered

(These kits will replace the seals on 1 cylinder)

Globe 12-5/8 "Spring Style" Seal Kit  

for 12-5/8 inch diameter Globe Cylinder

 Includes: Wiper, Seal, Spring, Complete Set of Assorted Gaskets (You'll have a few left over) and Installation Instructions. Uses spring for expander instead of "rubber ribbed" style expanding method. (Spring style may be a little easier for you to install than the ribbed style is.)

$419.00 Delivered

         

GLOBE Equalizer Parts In Stock! 

(Complete Kits Further Down)

GLOBE Equalizer Image Link

All Globe Equalizer Parts Available To Ship Today!

(Contact us for a quote on auto-locking equalizer mechanisms)

Some Parts in above image listed below:

CALL 630-678-9010 TO ORDER PARTS BELOW AND GET A 10% DISCOUNT

 

 

 Globe Rack Bar Manual Lock Mechanism - You get TWO LOCKING BLOCKS that slide onto the rack bar at any point and the lift will not lower past that point

  $219.00 Per Kit Delivered 

     

 Rack Bar (Manual Locking) $529.00 Each Delivered 

  9410 weighs 43 lbs

 Rack Bar (4 position) Auto Locking $529.00 Each Delivered 

9409 weighs 43 lbs

Pinion Gear with Keyway  $145.00 Each Delivered 

    (Globe Gears have 18 Teeth On Them)

NON-LOCKING (left or right) Equalizer Housing Bracket  $275.00 Each Delivered

        (Use with 9410 Manual Locking Rack Bars)

LOCKING (Left Hand) Equalizer Gear Housing Bracket  $398.00 Each Delivered  

with locking hardware included

LOCKING (Right Hand) Equalizer Housing Bracket  $398.00 Each Delivered  

with locking hardware included

(Use with 9409 Auto Locking Rack Bars)

 

Both Left & Right LOCKING Equalizer Gear Housings 

with locking hardware included

$789.00 Delivered

  (Use with 9409 Auto Locking Rack Bars)

 

Locking Hardware Repair Kit Complete For One Housing Bracket, will rebuild one locking mechanism on one housing. (Must be locking type equalizer housing bracket to begin with, won't convert non-locking type)

One kit $150.00 Delivered  

   

 

 

GLOBE Equalizer Shafts

IMPORTANT! Measure the distance between the piston centers to determine the length of the correct equalizer shaft, the shaft sizes below reflect the distance between the piston centers, not necessarily the length of the shaft itself. 

36 inch piston centers equalizer shaft $198.00 Each Delivered 

 

 

36 inch piston centers LOCKING equalizer shaft $198.00 Each Delivered 

Use locking shafts with locking housing brackets

---

 

39 inch piston centers equalizer shaft $239.00 Each Delivered 

 

 

39 inch piston centers LOCKING equalizer shaft $239.00 Each Delivered 

Use locking shafts with locking housing brackets

 

---

 

 

42  inch piston centers equalizer shaft $239.00 Each Delivered

42  inch  piston centers LOCKING equalizer shaft $239.00 Each Delivered

Use locking shafts with locking housing brackets

---

 

 

46  inch piston centers equalizer shaft $249.00 Each Delivered

46  inch  piston centers LOCKING equalizer shaft $249.00 Each Delivered

Use locking shafts with locking housing brackets

---

 

 

57-1/2 inch piston centers equalizer shaft  $259.00 Each Delivered 

 

57-1/2 inch piston centers LOCKING equalizer shaft  $259.00 Each Delivered 

Use locking shafts with locking housing brackets

---

 

 

83-1/2 inch piston centers equalizer shaft  $279.00 Each Delivered 

 

83-1/2 inch piston centers LOCKING equalizer shaft  $279.00 Each Delivered 

Use locking shafts with locking housing brackets

Call for 88 inch piston centers equalizer shaft

---

Complete Manual & Locking Equalizer Kits 

For Globe In-Ground lifts

Manual Kits Include 2 rack bars, 2 pinion gears, 2 gear housings,  1 shaft and hardware kit.

Call 630-678-9010 for the "Locking" type equalizer kit you want, but first

measure the distance between the center of both pistons for the "Piston Centers" Measurement